9/11/2023 0 Comments Zebra zt410 direct thermal setup![]() ![]() ![]() Print.printer_.print_unwriteable_margin_right Print.printer_.print_unwriteable_margin_left Print.printer_.print_unwriteable_margin_bottom Update the following settings to their correct value:.This will group all of the settings that you need to format together. In the address bar, enter about:config.To make sure your labels print correctly and alligned, you need to format the following Firefox settings: Note: You can change the units from millimeters to inches from the Units submenu. On your computer, select Start menu > Control Panel. If you computer hasn't installed automatically after connecting it to a USB port on your computer and powering it, please see Installing your Zebra ZD410 manually on Windows before continuing. Zebra EPL2 driver for normal, small and alternative labels In the Printer Software window, select the correct driver for your label size:.Then, from the Use drop-down, select Select Software. In the Add window, select your Zebra ZD410.At the bottom of the left section, select + > Add Printer or Scanner.On your computer, at the top-left of your screen, select > System Preferences.Before you continue, make sure your computer is connected to a USB port on your computer and that it's powered on. The steps you need to follow to add your printer to your computer depend on its operating system. This will make sure that they're correctly aligned and ready to print. You can also quickly press the feed button (middle button) twice before printing. If you insert a new label roll of the same size, your printer will remember the settings from the calibration you did with the initial label roll. Note: Calibrating your label printer is only necessary when you insert a new label roll of a different size. The printer will measure and feed a few blank labels. To do so, hold down the pause and cancel buttons for two seconds and release. This will make sure that your labels will print correctly. Push the lid closed until both yellow latches snap shut.įor your label printer to recognize the size of your labels, you need to calibrate it.Flip the labels up and align the movable sensor to the center position.Pull the labels out past the cutter at the front of the printer.Make sure the label roll is secure and turning freely. ![]() Release the roll guides and push them together.Pull the yellow roll guides apart and insert the label roll with the labels facing upwards.Pull the yellow latches on both sides of the printer towards you and lift the printer's lid open.Label rolls are purchased separately from your label printer. Connect the other end of the USB cable to your computer.Connect one end of the USB cable to your label printer.Connect the power cord to the power supply and an electrical outlet.Connect the power supply to the back of your label printer.To connect your label printer, you need the power cable, the power adapter, and the USB cable. And dynamic QR codes provide additional “on-demand,” web-based support to resolve printer errors quickly.Note: You’ll receive an email in your inbox as soon as your hardware shipment has shipped. If you have further questions regarding your shipment, please contact the shipping carrier or Billing. The ZT510 is engineered to grow and change with your business needs in the future by simplifying hardware upgrades, integrating seamlessly with common device management software and streamlining software updates with easy-to-use Link-OS applications.Īdditional capabilities that improve performanceįrom the fast processor that enables quick throughput of even complex graphics to the optional USB Host card slot conveniently located on the back of the printer, the ZT510 optimizes performance at every turn. Optional Parallel, 802.11a/c with Bluetooth® 4.0, USB Host and IPv6 are also available. It’s even ENERGY STAR® qualified to further protect your bottom line.Ī variety of connectivity options for flexible configurationįeaturing a variety of standard communication options including USB, Serial, Gigabit Ethernet and Bluetooth® LE, the ZT510 is easy to integrate into existing systems and connect to various networks. It provides high duty cycle, rugged reliability, fast processing, advanced Link-OS™ capabilities and all the basic features you need-without the added cost of those you don’t. The ZT510 is ideal for cost-conscious companies, offering next-generation print performance at an exceptional value. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |